HW Dev Engineer-Payload, Hardware Development
Job Description
Project Kuiper is an initiative to launch a constellation of Low Earth Orbit satellites that will provide low-latency, high-speed broadband connectivity to unserved and underserved communities around the world.A day in the life:As an Hardware Engineer, you will have the opportunity to work on some of the most innovative, challenging, and exciting phased array antenna systems in industry right now. You will engage with an experienced team to conceive and design phased arrays aimed at delighting customers with affordable, reliable, high bandwidth connectivity. You will work closely with Project Kuiper’s various sub-teams and engage third party suppliers to drive product definition, design, optimization, implementation, and test. The Hardware Engineer will have a complete understanding of how their design changes impact downstream partners such as operations, supply chain, product management, and reliability. Amazon strongly believes in Ownership and you will have the opportunity to own your designs from concept through production. You will own or contribute to the following:- Own PCBA development from concept through production- Design and optimize different blocks of electronics sub-systems- Design high-speed digital and/or RF circuitry in collaboration with various teams- Lead and review schematic capture and PCB layout- Lead PCB vendor engagement for DFM review- Optimize PCB stack-up for performance and cost- Generate test plans/procedures based off high level requirement definition- Complete board bring-up and perform test campaigns for different modules and subsystems- Design of automated test systems, test fixtures, and factory test- Support the transition of the designs to productionAbout the hiring group:The payload antenna team is responsible for the architecture, design, implementation, validation, qualification, and new product introduction to manufacturing for all satellite phased arrays. These antenna systems will meet performance requirements defined by the RF/modem team as well as environmental and reliability requirements defined by the mechanical team. To this end, the antenna team collaborates closely with all the partner teams including silicon, power, mechanical, thermal, modem, RF/Coms system, and SW teams.Export Control Requirement:Due to applicable export control laws and regulations, candidates must be a U.S. citizen or national, U.S. permanent resident (i.e., current Green Card holder), or lawfully admitted into the U.S. as a refugee or granted asylum.
Locations
- United States, WA, Redmond, Redmond, WA, United States
Salary
Salary not disclosed
Estimated Salary Rangehigh confidence
140,000 - 220,000 USD / yearly
Source: ai estimated
* This is an estimated range based on market data and may vary based on experience and qualifications.
Skills Required
- - 4+ years of industry experience in mixed signal PCBA designintermediate
- - 3+ years of experience in using schematic tool (Mentor Graphics Xpedition, Cadence OrCad, or Altium Designer)intermediate
- - 2+ years of experience in using lab equipment, including oscilloscopes, logic analyzers, and multi-metersintermediate
- - 1+ years of experience in high-speed digital design (SERDES, Ethernet, PCIe, etc...)intermediate
Required Qualifications
- - Bachelor's degree in electrical engineering or equivalent (degree in electrical engineering or equivalent)
- - 4+ years of industry experience in mixed signal PCBA design (experience, 4 years)
- - 3+ years of experience in using schematic tool (Mentor Graphics Xpedition, Cadence OrCad, or Altium Designer) (experience, 3 years)
- - 2+ years of experience in using lab equipment, including oscilloscopes, logic analyzers, and multi-meters (experience, 2 years)
- - 1+ years of experience in high-speed digital design (SERDES, Ethernet, PCIe, etc...) (experience, 1 years)
Preferred Qualifications
- - Master's degree in electrical engineering or equivalent (degree in electrical engineering or equivalent)
- - 1+ years of experience with signal and/or power integrity (experience, 1 years)
- - Experience with PCB layout tools (experience)
- Our compensation reflects the cost of labor across several US geographic markets. The base pay for this position ranges from $105,600/year in our lowest geographic market up to $185,000/year in our highest geographic market. Pay is based on a number of factors including market location and may vary depending on job-related knowledge, skills, and experience. Amazon is a total compensation company. Dependent on the position offered, equity, sign-on payments, and other forms of compensation may be provided as part of a total compensation package, in addition to a full range of medical, financial, and/or other benefits. For more information, please visit https://www.aboutamazon.com/workplace/employee-benefits. This position will remain posted until filled. Applicants should apply via our internal or external career site. (experience)
Documents
Application Instructions
https://www.amazon.jobs/en/jobs/3113983